Every job includes inspection, containment, drying, removal of unsalvageable board, antimicrobial treatment, and the drywall rebuild. Paint and texture matching are included; decorative finishes and full-room repaints are quoted separately if you want them. Here is what you get on a standard job.
Moisture meter, hygrometer, thermal imaging camera, and boroscope readings on every wall in the affected area. You get a marked map showing wet zones and the cut line before anything is opened. This is the step that decides the whole scope.
Plastic barriers and negative air keep spores out of the rest of your home. We HEPA-vacuum the framing and surrounding surfaces after demolition so no loose mold settles back into the cavity you are keeping.
Equipment runs 24 to 72 hours with daily moisture readings until the framing hits dry standard. We text you the numbers. This is the difference between a fix and a repeat call next spring.
Treated framing and saved drywall get an antimicrobial application followed by a primer sealer such as Kilz. That locks the surface and stops stains and odor from bleeding through the new finish.
New mold-resistant panels, tape, joint compound, sanding, and a texture match to the surrounding wall. We prime and leave the room broom-clean, paint-ready, and warrantied.
Mold remediation water damaged drywall rockwall TX is the process of stopping active mold growth inside wet drywall, removing the material that cannot be saved, and rebuilding the wall so it is dry, treated, and sealed. It starts with moisture mapping using a moisture meter, hygrometer, and thermal imaging camera to find every wet cavity behind the paint. From there we set containment, run dehumidifiers and air movers, cut out soft or sagging board with a drywall saw, and treat the framing and paper face before anything new goes back up.
Rockwall sits on the east side of Lake Ray Hubbard, and that lake effect is real. Spring storms push water through window frames and roof penetrations, and summer humidity keeps wall cavities damp long after the storm passes. We see drywall bubbling, water stains, and a musty odor in homes from The Harbor to Stone Creek. If you are searching how to remove mold from water damaged drywall in rockwall, the answer is always the same: dry it, test it, cut out what is compromised, and rebuild with mold-resistant drywall.
Every job follows the same five stages, whether it is one wall behind a washing machine or a whole ceiling after a roof leak. Here is exactly what happens after you call.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Moisture meter and hygrometer
Reads moisture content in drywall and the relative humidity in the cavity, giving us a number to dry to instead of a guess.
Thermal imaging camera
Shows temperature differences behind the paint so we can see where water traveled without opening the whole wall.
Boroscope
Slides into a small hole to let us look at the back of the board and the framing for hidden mold growth before we cut.
Dehumidifier and air mover
Pulls moisture out of the air and drives airflow across wet surfaces so the cavity dries in 24 to 72 hours.
Drywall saw and joint knife
Cuts clean openings at the marked line and feathers joint compound during the rebuild so the patch disappears.
Drywall sander and stud finder
Smooths the finished patch and locates framing so new panels land on solid studs, not just the old screw holes.
IICRC S500 drying standard
We dry to documented moisture content at the framing, not to the touch. Readings are logged daily and shared with you, which is also what your insurance adjuster wants to see.
Containment with negative air
Plastic barriers and negative air pressure keep spores and dust inside the work zone. It protects the rest of your home and it is standard practice on every mold job we run.
Cut 12 inches past the wet line
We remove drywall a foot beyond the last wet reading because moisture wicks farther than the visible stain. Cutting tight to the stain is the most common reason mold comes back.
Antimicrobial treatment plus primer sealer
Treated framing and saved board get an antimicrobial application, then a primer sealer such as Kilz. That combination stops regrowth on the surface and blocks stains from bleeding through.
01
What we do: We extract standing water, set containment, and run dehumidifiers and air movers on the cavity. Once readings are dry we treat the framing, cut out the soft panel, and rebuild with mold-resistant drywall.
→ The wall is dry, treated, and paint-ready in three to four days, and the laundry room is back in service without a mold problem.
02
What we do: We map the wet zone, dry the cavity, and check the back of the board with a boroscope. Colonized sections come out, framing gets treated, and we re-rock and texture-match the wall.
→ Storm damage is repaired and documented for insurance, and the wall handles the next lake-effect humid stretch without a repeat.
03
What we do: We cut the sagging ceiling section, dry the joists, treat for mold, and replace the insulation before closing it back up with new drywall and a texture match.
→ The ceiling is flat, sealed, and odor-free, and the upstairs leak is documented so the same failure does not soak it again.
04
What we do: We inspect the cavity, confirm whether mold is present, dry the framing, and seal the stain with a primer sealer before rebuilding the damaged section.
→ The stain stops bleeding through, the wall is solid again, and you know exactly where the leak was so it can be fixed at the roof.
Rockwall sits against Lake Ray Hubbard, and that changes how wet drywall behaves here. Lake-effect humidity keeps wall cavities damp long after a storm passes, and spring storm cells push water through window frames, roof penetrations, and garage walls. Homes in The Harbor and Rockwall Lakefront take the worst of it. We also work a lot of slab-on-grade houses where a slow supply-line leak under a cabinet wicks up the wall for weeks before anyone notices. On the rebuild side, Rockwall County follows standard Texas residential code, so replacement board has to be the right thickness and fastened to framing, not patched over soft gypsum. If you need emergency mold remediation water damaged drywall rockwall TX after a burst line, call before noon and we can usually be on site the same day with drying equipment. Typical 2026 pricing for a single wall in this area runs $650 to $1,400 once drying, treatment, and rebuild are included.
The Harbor
Lakefront and near-lake homes here see wind-driven rain against window frames, which is one of our most common wet-wall calls.
Stone Creek
Two-story homes with upstairs bathrooms; a failed supply line sends water straight into the ceiling below.
Chandlers Landing
Mature landscaping and irrigation lines near the foundation keep exterior walls damp through the summer.
Rockwall Lakefront
Direct lake exposure means storm-driven water and high ambient humidity, so cavities dry slower here.
Lake-effect humidity through summer
Wall cavities stay damp longer, so we run drying equipment an extra 12 to 24 hours compared to inland jobs and verify with a hygrometer before closing the wall.
Spring storm cells and wind-driven rain
Water pushes through window frames and roof penetrations, so we inspect above and beside the visible stain, not just the wet spot.
Slab-on-grade construction
Slow leaks under cabinets wick up the wall quietly, so we check the bottom plate and the first 24 inches of drywall on every kitchen and laundry call.
Most of the calls we get start with one of these four symptoms. Each one means moisture is still in the wall, and each one gets worse on its own.
Problem
A persistent musty smell usually means active mold growth behind the paint, and it spreads into adjacent rooms and closets within weeks.
Our Fix
We locate the source with a thermal imaging camera and boroscope, contain the area, dry the cavity, and remove the colonized board. Odor is gone when the moisture is gone, not before.
Problem
Bubbled paint traps moisture against the gypsum and hides how far the water has traveled. Left alone, the panel softens and the damage spreads along the stud bay.
Our Fix
We open the bubble, read moisture at the framing, and dry the cavity. If the core is still firm we treat and seal it; if it is soft, we cut back 12 inches past the wet line and rebuild.
Problem
Soft drywall has lost its structural strength and can sag or fall, and the paper face is the perfect food source for mold.
Our Fix
Soft board comes out. We remove it, dry and treat the framing, replace any wet insulation, and install new mold-resistant drywall so the wall is solid and code-correct.
Problem
A stain that reappears after painting means the moisture source was never fixed, and each repaint cycle hides a bigger problem behind it.
Our Fix
We find and stop the source, dry the cavity, then seal with a primer sealer so the stain cannot bleed through. No source fix, no repaint, no exceptions.
Mold does not wait for a convenient day. These are the four outcomes our customers care about most, and the ones we build every job around.
Stop the Spread Fast
Mold can colonize a wet paper-faced panel in 24 to 48 hours. We set containment and start drying the same day we arrive, which keeps spores out of the rest of your house. Most single-wall jobs in rockwall TX drywall mold treatment are stabilized within one visit.
Save the Wall When Possible
Not every wet panel has to come down. If the paper face and gypsum core still hold together, we dry it in place, treat it, and seal it with a primer sealer. That saves you the cost of new drywall panels, tape, and finishing on roughly a third of the jobs we inspect.
Rebuild With Mold-Resistant Board
When board has to go, we replace it with mold-resistant drywall from USG Sheetrock or Georgia-Pacific, taped with FibaFuse or mesh tape and finished with joint compound. You get a wall that looks factory-new and handles the next humid Rockwall County summer far better than the original.
Insurance-Ready Documentation
We photograph moisture readings, mark the water line, and log every cut before we make it. That record is what your adjuster needs to approve drywall mold removal near me rockwall claims. We have walked hundreds of homeowners through the paperwork, and we will walk you through yours.
Google ★★★★★4.9
They found the leak behind our laundry wall, dried it for two days, and rebuilt the drywall so you cannot see the patch. The moisture readings they texted me every morning made the whole thing feel honest. Would call them again without shopping around.
Yelp ★★★★★5.0
Our ceiling was sagging after an upstairs toilet leak and they handled everything from the cut to the texture match. They documented it for our insurance and the adjuster approved it the first time. Clean work, no surprises on the bill.
BBB ★★★★★4.8
Storm water came in around a window and soaked the wall. They were out the same day, explained why the drying step mattered, and did not try to sell me a full-room rebuild. The musty smell is gone and the wall is solid.
Our crews work on wet drywall every week, not once a season. We hold IICRC certification for water damage restoration and mold remediation certification, and we carry Texas state licensed contractor status along with EPA Lead-Safe certification for homes built before 1978. That matters in older Rockwall County neighborhoods where lead paint and original gypsum board are still in the walls. We follow IICRC S500 drying standards on every job, document moisture readings before and after, and use calibrated meters rather than a hand-feel guess. When we say a wall is dry, there is a number behind it.
Real answers to the questions we hear most often from local homeowners and property managers.
The rebuild side of the job. Once we have dried and treated the cavity, this service puts new panels, tape, and joint compound back on the wall so it is paint-ready. Most mold jobs in rockwall finish with this step.
View Water Damaged Drywall RepairFor burst pipes and storm intrusion that happen at 2 a.m. We tarp, extract, and set drying equipment fast, which is what keeps a wet wall from becoming a mold job in the first place. Same-day response across Rockwall County.
View Emergency Water Damage Drywall RestorationMoisture meter, thermal imaging camera, and boroscope readings that tell you what is wet behind the paint. This is the inspection we run before any mold remediation, and it is how we decide what stays and what comes out.
View Drywall Water Damage Assessment and InspectionRoof leaks and upstairs supply lines leave ceilings sagging and stained. We cut out the soft section, dry the joists, treat for mold, and re-rock the ceiling with a texture match. Common in two-story homes around The Harbor.
View Ceiling Water Damage RepairInterior and exterior wall repair after a leak or flood line. We open the cavity, dry it, treat any mold growth, replace insulation, and close the wall with mold-resistant drywall and a sealed finish.
View Wall Water Damage RepairBrown rings and tide lines do not always mean mold, but they always mean moisture. We seal the stain with a primer sealer so it cannot bleed through new paint, and we check the cavity first to rule out hidden mold growth.
View Drywall Water Stain Removal and SealingCall, text, or send us a message and we will get a technician out to meter the wall and quote the repair. Same-day estimates are standard, and emergency calls get answered around the clock. If you are dealing with an active leak, tell us on the phone so we can bring drying equipment on the first trip.
Phone
9728844781Address
1375 Mims Rd, Rockwall, TX 75032
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available
